For best experience this site requires Javascript to be enabled. To enable on your browser, follow our accessibility instructions.

LPC4320FBD144: High Performance 32-bit Microcontroller (MCU) based on Arm^® Cortex^®-M4/M0 Cores

Overview

The LPC4320FBD144 is an Arm Cortex-M4 based digital signal controller with an Arm Cortex-M0 coprocessor designed for embedded applications requiring signal processing. The Arm Cortex-M4 core offers single-cycle Multiply-Accumulate and SIMD instructions and a hardware floating-point unit to support signal processing while the M0 coprocessor handles I/O and digital control processing. The LPC4320FBD144 includes 168 kB of data memory, one High Speed USB 2.0 Host/OTG/Device, advanced configurable peripherals such as the State Configurable Timer (SCT), Serial General Purpose I/O (SGPIO), and SPI Flash Interface (SPIFI) as well as an external memory controller and multiple digital and analog peripherals.

Features

Arm Cortex-M4 processor, running at frequencies of up to 204 MHz
Arm Cortex-M4 built-in Memory Protection Unit (MPU) supporting eight regions
Arm Cortex-M4 built-in Nested Vectored Interrupt Controller (NVIC)
Hardware floating-point unit
Non-maskable Interrupt (NMI) input
JTAG and Serial Wire Debug (SWD)
System tick timer
Arm Cortex-M0 co-processor running at frequencies of up to 204 MHz
200 kB SRAM for code and data use
Two 32 kB SRAM blocks with separate bus access
32 kB ROM containing boot code and on-chip software drivers
32 bit One-Time Programmable (OTP) memory for customer use
Serial GPIO (SGPIO) interface
State Configurable Timer (SCT) subsystem on AHB
Quad SPI Flash Interface (SPIFI) with four lanes and up to 40 MB per second
One High-speed USB 2.0 Host/Device/OTG interface with DMA support
One 550 UART with DMA support and full modem interface
Three 550 USARTs with DMA and synchronous mode support
One C_CAN 2.0B controller with one channel
Two SSP controllers with FIFO and multi-protocol support
One SPI controller
One Fast-mode Plus I2C-bus interface with rates of up to 1 Mbit/s
One Fast-mode I2C-bus interface
Two I2S interfaces
External Memory Controller (EMC) supporting external SRAM, ROM, flash, SDRAM
Secure Digital Input Output (SDIO) card interface
Eight-channel General-Purpose DMA (GPDMA) controller
Up to 83 General-Purpose Input/Output (GPIO) pins
Four general-purpose timer/counters with capture and match capabilities
One motor control Pulse Width Modulator (PWM) for three-phase motor control
One Quadrature Encoder Interface (QEI)
Repetitive Interrupt timer (RI timer)
Windowed watchdog timer (WWDT)
Ultra-low power Real-Time Clock (RTC) on separate power domain
Alarm timer; can be battery powered
One 10-bit DAC with DMA support and a data conversion rate of 400 kSamples/s
Two 10-bit ADCs with DMA support and a data conversion rate of 400 kSamples/s
Two 128-bit secure OTP memories for AES key storage and customer use
Crystal oscillator with an operating range of 1 MHz to 25 MHz
12 MHz Internal RC (IRC) oscillator trimmed to 1 % accuracy
Ultra-low power Real-Time Clock (RTC) crystal oscillator
Three PLLs allow CPU operation up to the maximum CPU rate
Clock output
Single 3.3 V (2.2 V to 3.6 V) power supply with on-chip DC-to-DC converter
RTC power domain can be powered separately by a 3 V battery supply
Four reduced power modes
Processor wake-up from Sleep mode via wake-up interrupts
Brownout detect with four separate thresholds for interrupt and forced reset
Power-On Reset (POR)
See selection guide for features per type

Target Applications

Industrial
Consumer
White goods
RFID readers
e-Metering

Features

Target Applications

Industrial
Consumer
White goods
RFID readers
e-Metering

Application Notes

sot486-1_3d

sot486-1_3d

sot486-1_3d

.

Target Applications

Automotive

Industrial

Mobile

Smart Home

Technologies

Complementary products for your application