Get Started with the RDK01DB1563

2.1 Board description

The TEA2016DB1514 interface board is a development tool that enables setting TEA2016 controller parameters from a computer. The available Ringo TEA2016 development software provides a graphical user interface (GUI) that can be installed on a computer.

The interface and software are intended for engineering work in lab environment as part of power supply development. It is not suitable for consumer or industrial purpose usage.

2.2 Additional board support

Refer to UM11527, RDK01DB1563 interface board and Ringo software package for additional software details and UM11235 (extended user manual for the interface board).

Copy the zip file from the USB stick or download it to a folder on your computer. The x64 is for 64-bit operating systems; the x86 is for 32-bit operating systems. Unzip the file.

For the Ringo software to work, the FT232H driver for the USB-I²C interface needs to be installed. This installation happens automatically when you connect the interface for the first time via USB. If the driver is not installed automatically, you can use the included drivers to do this manually (a video on the get started page shows how to do this).

Important:

When the FT232H driver is not installed, the Ringo software does not work.

The Ringo program needs no installation. It can be started by double-clicking on Ringo.exe. Keep the other files and folders in the same directory because Ringo makes use of it.

3.1 User manual and tutorial videos for the Ringo software

A user manual and videos are included in the Ringo GUI software for easy access to get familiar with using the software and getting to know the functions that are available.

Videos are available in Ringo for viewing on your local video player or via the NXP website in your browser:

• Introduction
• Read and write
• Information and protection
• Save settings in file
• Warning and power bar
• Read write lock and reset
• Search and connection quality

Additional videos are available at TEA2016AAT: Digital Controller for High-Efficiency Resonant Power Supply

3.2 Additional software support

Refer to UM11527, RDK01DB1563 interface board and Ringo software package for additional software details.

Power supply setup:

• The TEA2016DB1519v2 demo board contains a TEA2016AATdev sample that can communicate via I²C during operation. It is connected to the interface with a 3-pin connection.

IC programming board setup:

• Connecting a TEA2016DB1561 with a 6-pin cable provides reading or programming for TEA2016AAT ICs. If a TEA2016AATdev IC version is used, connect the 3-pin cable as well.

The switch on the interface selects the 3-pin or 6-pin connection.

4.1 Additional board support

Refer to UM11527, RDK01DB1563 interface board Ringo software package for additional software details and UM11235 (extended user manual for the interface board).

5.1 Ringo software

Q: Ringo.exe does not start.

• A1: To enable Ringo software to work, the USB-I²C interface driver (FT232) must be installed on the computer.
• A2: Make sure you are using a compatible version: 32-bit or 64-bit.
• A3: Ringo is made for Windows operating systems. On other operating systems, it can be run via a Windows emulator.

Q: Can I work with Ringo without the interface connected?

• A1: Yes, when the USB-I²C interface driver (FT232) is already installed.
• A2: To get started the USB-I²C interface driver (FT232) must be installed on the computer to enable Ringo software to work. For this, the interface needs to be connected (one time) to install the driver.

Q: When I connect the USB-I²C interface, it does not work.

• A1: To make the FT323 module operational, a driver is required. The driver is often automatically installed (plug and play). However, sometimes a manual install is required. Several drivers are included in the Ringo zip package. Watch the video “installing USB driver manually” on the NXP website.
• A2: When the driver has been installed, but still it does not work: Completely (‘delete the driver software for this device’) remove the driver and select another driver included in the package. Or visit the FTDI chip website for more information or driver versions.

5.2 USB - I²C interface

Q: Can I change settings in an TEA2016AATdev (development type) IC on the power supply when the power supply is not running?

• A1: Yes. When you apply a low mains voltage of 50 V (AC), the HV source supplies the IC and it can communicate via I²C. But the power supply does not start because the mains voltage is still too low.
• A2: Yes. If an external power supply of 20 V is (temporarily) connected to SUPIC, the IC is operational without starting the power supply.

Q: Can I change settings in a TEA2016AAT IC (nondevelopment type) on the power supply?

• Yes, but it is more complicated than with the TEA2016AATdev. The AN12330 application note shows how to do it in section "Programming ICs in the application". You cannot make changes during operation because the pins for I²C communication have a different function during operation.

Q: There is no communication with the IC.

• A1: Check if the switch on the interface is in the correct position: 3-pin or 6-pin.
• A2: Check if the correct cable is connected (or both when using the programming board).
• A3: Check if signal disturbance is blocking communication.

Q: I want to modify the board or do repairs on the board. Is there a circuit diagram?

• A1: The circuit diagram is included in the UM11235 user manual. This document is available in the document folder on the USB stick or in the Help tab in Ringo.

Q: What is the function of the LEDs on the board?

• A1: The Ringo software can use them for indicating that the I²C connection is OK. The indication differs between Ringo versions. In general, slow blinking indicates no communication with the IC. And fast blinking indicates correct communication with the IC.

5.3 RDK01DB1563 kit

Q: Can I also work with TEA2016AATdev without buying an extra kit?

• A1: Yes. The TEA2016 IC can be used in a power supply. In this case, the IC standard parameter settings are used.
• A2: When you want to use the option to modify the TEA2016 settings for optimizing your design, the software and an interface board are necessary.

6.1 Product summary page

The product summary page for TEA2016AAT is available at https://www.nxp.com/TEA2016AAT.

6.2 Tool summary page

The tool summary page for RDK01DB1561 board is at http://www.nxp.com/RDK01DB1563.

The page provides overview information, technical and functional specifications, ordering information, documentation and software. The Get Started guide provides quick-reference information applicable to using the RDK01DB1563 board, including the downloadable assets.

6.3 References

In addition to our TEA2016AAT: digital LLC+PFC combo controller for resonant power supply, you may also want to visit:

Gate driver pages:

• TEA19161T: Resonant Power Supply Control IC
• TEA19162T: PFC Controller

Hardware pages:

• Analog Toolbox

Software pages:

• Analog Expert Software and Tools

6.4 Buy the board

RDK01DB1563: TEA2016AAT development interface board

Buy