TWR-MCF51JE: ColdFire Flexis MCF51JE Low-Power USB Tower System Module

Overview

TWR-MCF51JE Evaluation Board
TWR-MCF51JE Evaluation Board

TWR-MCF51JE Evaluation Board  

Introducing Five New Microcontrollers (MCUs) for Medical Solutions

Introducing Five New Microcontrollers (MCUs) for Medical Solutions  

Specifications

Supported Devices

Processors and Microcontrollers

ColdFire® V1 Processors
  • MCF51JE : Flexis™ 32-bit ColdFire®. V1 Microcontrollers
8-Bit S08 MCUs
  • S08JE : 8-bit Flexis USB JE MCUs

MoreLess

Technical and Functional Specifications

Debug Integrated open source BDM debugging tool
Size Small form factor (59 mm x 90 mm)

Buy

  • TWR-MCF51JE   Development

  • Tower System, ColdFire MCU Module, MCF51JE, Low Power USB
    • Part Number TWR-MCF51JE contains:
      • TWR-MCF51JE board with a MCF51JE256 32-bit MCU
      • DVD with software, training and collateral
      • Quick Start Guide document
    • Part Number TWR-MCF51JE-KIT also contains:
      • TWR-SER - Tower System Serial Module
      • TWR-ELEV - Tower System Elevator Modules
      • Necessary cables
    • TWR-MCF51JE
    • 1 @ US
    • $69.00
    • Use Coupon
    • Distributor

    Don't have an NXP coupon? You can purchase this product from one of our authorized distributors.

    • TWR-MCF51JE-KIT
    • 1 @ US
    • $119.00
    • Use Coupon
    • Distributor

    Don't have an NXP coupon? You can purchase this product from one of our authorized distributors.

1579109330588723448640

Design Resources

Documents   ( 7 )

Design Resources   ( 1 )

Documents

Application Note  ( 3 )

  • Using the MM/JE Flexis® Families for Infrared Communication

    This application note shows how to easily migrate the communication protocol C12.18 which is already implemented on the MCF51EM256 on to new devices.This is explained in the NXP application note titled Using the MCF51EM Family for Infrared Communication (document AN3938).

    • PDF
    • Rev 0
    • Jul 30, 2010
    • 796.4 KB
    • AN4116
    • English
    • Associated File: AN4116SW

  • AN4115, IrDA Driver and SD Card File System on MM/JE Flexis® Families - Application Notes

    AN4115: This application note discusses a physical layer driver used to establish IrDA communication on NXP devices in the MM/JE Flexis® families, using the Carrier Modulator Timer (CMT) as transmitter and a Timer/Pulse-Width Modulator (TPM) as receptor. It also explains a driver to handle a Secure Digital (SD) card through a Serial Peripheral Interface (SPI) module.

    • PDF
    • Rev 0
    • Jul 30, 2010
    • 445.8 KB
    • AN4115
    • English
    • Associated File: AN4115SW

  • Dynamic LCD Driver Using GPIO Pins

    This application note explains how the twisted nematic (TN) liquid crystal displays (LCDs) work and how these kinds of LCDs can be controlled using the GPIO pins of a microcontroller. There are two ways to control the TN LCDs, statically and dynamically. The driver discussed in this document is intended to drive dynamic LCDs. The dynamically driven LCDs require a pure AC voltage waveform applied to the electrodes of the LCD. Each electrode needs one backplane electrode and one frontplane terminal to be disp

    • PDF
    • Rev 0
    • Apr 26, 2010
    • 5.5 MB
    • AN3412
    • English
    • Associated File: AN3412SW

Errata  ( 1 )

  • OSBDM ERRATA

    • PDF
    • Rev 2.0
    • Aug 10, 2011
    • 313.7 KB
    • OSBDM_ERRATA
    • English

Fact Sheet  ( 1 )

  • MCF51JE256/128 Ultra-low-power MCU with USB connectivity - Fact Sheet

    MCF51JE256FS: The MCF51JE256/128 (JE256/128) provides ultra-low-power operation, USB connectivity and high measurement accuracy, all in a single 32-bit microcontroller, allowing designers to develop a more fully featured system at a lower cost. The JE256/128 integrates high-resolution ADC and DAC modules and a rich peripheral set including a USB 2.0 host/device/OTG controller, multiple serial interfaces and an external bus interface.

    • PDF
    • Rev 2
    • Feb 18, 2020
    • 268.6 KB
    • MCF51JE256FS
    • English

Supporting Information  ( 2 )

  • Tower Mechanical Drawing

    Tower® Mechanical Drawing

    • PDF
    • Rev E
    • May 21, 2012
    • 228.4 KB
    • 900-76126_TWR-MECHDRW
    • English

  • Tower Configuration Tool

    Tower® Configuration Tool Long Description: Excel based configuration tool for the Tower System. Provides pinout information for Tower Elevator Primary and Secondary Connectors and tools for compatibility checking between existing Tower Modules and designing new Tower Modules.

    • ZIP
    • Rev 1.02
    • Jan 15, 2010
    • 203.8 KB
    • TOWER_CONFIG_TOOL
    • English

Design Resources

Design Tools & Files  ( 1 )

Printed Circuit Boards and Schematics  ( 1 )