Security and Authentication
Contact Readers
- TDA8007BHL
- TDA8020HL
- TDA8023TT
- TDA8024
- TDA8026ET
- TDA8029HL
- TDA8034
- TDA8034AT
- TDA8035HN
- TDA8037
TDA8023TT

TDA8023TT: Low power IC card interface

Overview

The TDA8023 is a complete cost-efficient, low-power analog interface for synchronous or asynchronous smart cards. It can be placed between the card and the microcontroller with very few external components to perform all supply, protection and control functions.

MoreLess

Features

I²C-bus controlled IC card interface in TSSOP28
Supply voltage from 2.7 V to 6.5 V
Independant supply voltage V_DD(INTF) for interface signals with the microcontroller
Shutdown input for very low power consumption when the part is not used
Power reduction modes when the card is active
DC-to-DC converter for V_CC generation (capacitive doubler, tripler, or inductive, or follower automatically selected according to supply voltage and card voltage)
1 specific protected half duplex bidirectional buffered I/O line, with current limitation at ±15 mA, maximum frequency 1 MHz
2 auxiliary card I/O lines controlled by I²C-bus (C4 and C8)
V_CC regulation: 5 V, 3 V or 1.8 V ±8%, I_CC< 55 mA, current spikes of 40 nAs up to 20 MHz, with controlled rise and fall times, filtered overload detection approximately 80 mA, current limitation about 120 mA
Thermal and short-circuit protections on all card contacts
Automatic activation and deactivation sequences: initiated by software or by hardware in the event of a short-circuit, card take-off, overheating, V_DD or V_DD(DCDC) drop-out
Enhanced ElectroStatic Discharge (ESD) protection on card side (> 6 kV)
20 MHz clock input
Clock generation for the card up to 10 MHz (CLKIN divided by 1, 2, 4 or 5) with synchronous frequency changes; stop HIGH or LOW or free running 1 MHz in cards Low-power mode; current limitation on pin CLK (C3)
RST signal (C2) with current limitation at 20 mA, controlled by an embedded programmable CLK pulse counter on asynchronous cards or by a register on synchronous cards
ISO 7816-3, GSM 11.11 and EMVCo 4.3 compatibility
Supply voltage supervisor for spike killing during power-on and emergency deactivation at power-off: threshold internally fixed or set via an external resistor bridge; pulse width internally fixed or set via an external capacitor
Card presence input with 10 ms built-in debouncing system
One interrupt signal INT

MoreLess

Features

I²C-bus controlled IC card interface in TSSOP28
Supply voltage from 2.7 V to 6.5 V
Independant supply voltage V_DD(INTF) for interface signals with the microcontroller
Shutdown input for very low power consumption when the part is not used
Power reduction modes when the card is active
DC-to-DC converter for V_CC generation (capacitive doubler, tripler, or inductive, or follower automatically selected according to supply voltage and card voltage)
1 specific protected half duplex bidirectional buffered I/O line, with current limitation at ±15 mA, maximum frequency 1 MHz
2 auxiliary card I/O lines controlled by I²C-bus (C4 and C8)
V_CC regulation: 5 V, 3 V or 1.8 V ±8%, I_CC< 55 mA, current spikes of 40 nAs up to 20 MHz, with controlled rise and fall times, filtered overload detection approximately 80 mA, current limitation about 120 mA
Thermal and short-circuit protections on all card contacts
Automatic activation and deactivation sequences: initiated by software or by hardware in the event of a short-circuit, card take-off, overheating, V_DD or V_DD(DCDC) drop-out
Enhanced ElectroStatic Discharge (ESD) protection on card side (> 6 kV)
20 MHz clock input
Clock generation for the card up to 10 MHz (CLKIN divided by 1, 2, 4 or 5) with synchronous frequency changes; stop HIGH or LOW or free running 1 MHz in cards Low-power mode; current limitation on pin CLK (C3)
RST signal (C2) with current limitation at 20 mA, controlled by an embedded programmable CLK pulse counter on asynchronous cards or by a register on synchronous cards
ISO 7816-3, GSM 11.11 and EMVCo 4.3 compatibility
Supply voltage supervisor for spike killing during power-on and emergency deactivation at power-off: threshold internally fixed or set via an external resistor bridge; pulse width internally fixed or set via an external capacitor
Card presence input with 10 ms built-in debouncing system
One interrupt signal INT

Data Sheets

Application Notes

Outline 3d SOT361-1

Outline 3d SOT361-1

Outline 3d SOT361-1

Previous Next

Target Applications

Banking terminals
Internet terminals
Set-top boxes
Portable IC card readers