Name: High Performance 32bit Microcontroller based on Arm174 Cortex174M3
Availability: BackOrder

For best experience this site requires Javascript to be enabled. To enable on your browser, follow our accessibility instructions.

The LPC1830FET180 is a high-performance, cost-effective Cortex-M3 microcontroller featuring 200 kB of SRAM, and advanced peripherals including Ethernet, High Speed USB 2.0 Host/OTG/Device and CAN 2.0B. Operating at speeds up to 180 MHz, the LPC1830 also features two new configurable peripherals: a SPI Flash Interface and a State Configurable Timer. All members of the series include a Wakeup Interrupt Controller allowing automatic wake from any priority interrupt as well as four reduced power modes: Sleep, Deep-Sleep, Power-Down, and Deep Power-Down.

See product image

Data Sheet

Application Notes

Product Details

Features

Arm Cortex-M3 processor, running at frequencies of up to 180 MHz
Arm Cortex-M3 built-in Memory Protection Unit (MPU) supporting eight regions
Arm Cortex-M3 built-in Nested Vectored Interrupt Controller (NVIC)
Non-maskable Interrupt (NMI) input
JTAG and Serial Wire Debug
ETM and ETB support
System tick timer
200 kB SRAM for code and data use
32 kB ROM containing boot code and on-chip software drivers
Crystal oscillator with an operating range of 1 MHz to 25 MHz
12 MHz internal RC oscillator trimmed to 1 % accuracy
Ultra-low power RTC crystal oscillator
Clock output
Two PLLs allow CPU operation up to the maximum CPU rate
Quad SPI Flash Interface with four lanes and data rates of up to 40 MB/s
10/100T Ethernet MAC with RMII and MII interfaces and DMA support
One High-speed USB 2.0 Host/Device/OTG interface with DMA support
One High-speed USB 2.0 Host/Device interface with DMA support
Four 550 UARTs with DMA support: one UART with full modem interface
One UART with IrDA interface
One C_CAN 2.0B controller with one channel
Two SSP controllers with FIFO and multi-protocol support
One Fast-mode Plus I2C-bus interface with monitor mode
One standard I2C-bus interface with monitor mode and standard I/O pins
One I2S interface with DMA support and with one input and one output
External Memory Controller (EMC)
SD/MMC card interface
Eight-channel General-Purpose DMA (GPDMA) controller
Up to 118 General-Purpose Input/Output (GPIO) pins
GPIO registers are located on the AHB for fast access
State Configurable Timer (SCT) subsystem on AHB
Four general-purpose timer/counters with capture and match capabilities
One motor control PWM for three-phase motor control
One Quadrature Encoder Interface (QEI)
Repetitive Interrupt timer (RI timer)
Windowed watchdog timer
Ultra-low power Real-Time Clock (RTC) on separate power domain
Alarm timer; can be battery powered
One 10-bit DAC with DMA support and a data conversion rate of 400 kSamples/s
Two 10-bit ADCs with DMA support and a data conversion rate of 400 kSamples/s
Hardware-based AES security engine programmable through an on-chip API
Two 128-bit secure OTP memories for AES key storage and customer use
Unique ID for each device
Single 3.3 V (2.2 V to 3.6 V) power supply with on-chip voltage regulator
RTC power domain can be powered separately by a 3 V battery supply
Four reduced power modes
Overdrive mode to increase CPU and bus clock frequency
Processor wake-up from Sleep mode via wake-up interrupts
Wake-up from Deep-sleep, Power-down, and Deep power-down modes
Brownout detect with four separate thresholds for interrupt and forced reset
Power-On Reset (POR)

Target Applications

Industrial
Consumer
White goods
RFID readers
e-Metering

Buy/Parametrics

‌ ‌ ‌	‌ ‌	‌ ‌	‌ ‌	‌ ‌	‌ ‌
‌ ‌ ‌	‌	‌	‌	‌	‌
‌ ‌ ‌	‌	‌	‌	‌	‌
‌ ‌ ‌	‌	‌	‌	‌	‌
‌ ‌ ‌	‌	‌	‌	‌	‌
‌ ‌ ‌	‌	‌	‌	‌	‌
‌ ‌ ‌	‌	‌	‌	‌	‌
‌ ‌ ‌	‌	‌	‌	‌	‌
‌ ‌ ‌	‌	‌	‌	‌	‌
‌ ‌ ‌	‌	‌	‌	‌	‌
‌ ‌ ‌	‌	‌	‌	‌	‌

Design Resources

Design Files

Quick reference to our design files types.

5 design files

Receive the full breakdown. See the product footprint and more in the eCad file.

Models
IBIS models for LPC18x0 and LPC43x0 FBD208

ZIPRev 2Mar 25, 2020 16:19:00368.25 KBIBIS_LPC18x0_LPC43x0FBD208
DownloadToggle Dropdown
- Add to Queue
- Remove from Queue
- Recommended for large file sizes.
- View Queue
Models
BSDL for LPC18xx and LPC43xx

ZIPRev 2Feb 27, 2018 11:57:00262.65 KBBSDL_LPC18XX_43XX

Account Required
DownloadToggle Dropdown
- Add to Queue
- Remove from Queue
- Recommended for large file sizes.
- View Queue
Models
IBIS models for LPC18x0 and LPC43x0 FET256-180-100

ZIPRev 1Jun 13, 2017 16:19:00371.35 KBIBIS_LPC18x0_43x0FET256-180-100

Account Required
DownloadToggle Dropdown
- Add to Queue
- Remove from Queue
- Recommended for large file sizes.
- View Queue
Symbols and Footprints
LPC43xx/LPC18xx Eagle symbols

ZIPRev 0Jun 3, 2016 00:00:0014.56 KBLPC43XX-EAGLE-SYM

Account Required
DownloadToggle Dropdown
- Add to Queue
- Remove from Queue
- Recommended for large file sizes.
- View Queue
Symbols and Footprints
LPC18XX_43XX_SCH Orcad Symbols

ZIPRev 1.0Apr 30, 2018 12:37:0051.02 KBLPC18XX_43XX_SCH_1

Account Required
DownloadToggle Dropdown
- Add to Queue
- Remove from Queue
- Recommended for large file sizes.
- View Queue

Hardware

Quick reference to our board types.

1-5 of 6 hardware offerings

Emulators, Probes, and Programmers
Universal Multilink Development Interface
Active

UMultilink
Emulators, Probes, and Programmers
PEmicro Cyclone programmer
Active

CYCLONE
Emulators, Probes, and Programmers
PEmicro Cyclone FX programmer

CYCLONE-FX
Additional hardware available. View our featured partner solutions.
Emulators, Probes, and Programmers
MCU-Link Pro Debug Probe
Active

MCU-LINK-PRO
Emulators, Probes, and Programmers
Universal Multilink FX High-Speed Development Interface
Active

U-MULTILINK-FX
Evaluation and Development Boards
MPC5646C Devlce and Target Adapters
Active

MPC5646C-DB

Show All

1-5 of 25 hardware offerings

Emulators, Probes, and Programmers
J-Link PLUS

JTAG/SWD debug probe with USB interface. Based on a 32-bit RISC CPU, it can communicate at high speed with the supported target CPUs. J-Link is used around the world in t...

By SEGGER Microcontroller GmbH Gold Partner
Emulators, Probes, and Programmers
Universal Access Device 3+ (UAD3+)

The UAD3+, equipped with up to 4 GB of trace memory and powerful interfaces to target and host, is the right solution for trace, multicore debugging, profiling and code c...

By PLS Development Tools Gold Partner
Emulators, Probes, and Programmers
J-Link BASE

Supercharge your IDE with the worlds fastest debug probe. The J-Link Flash download technology achieves a performance very close to the maximum speed possible. No other ...

By SEGGER Microcontroller GmbH Gold Partner
Emulators, Probes, and Programmers
Flasher Compact

Flasher Compact is the compact twin to the Flasher PRO, primarily designed for installation into production rigs or automated test equipment (ATE) where production space ...

By SEGGER Microcontroller GmbH Gold Partner
Emulators, Probes, and Programmers
Flasher Hub-4

SEGGER’s Flasher Hub-4 controls multiple Flasher Compacts (up to 24 via USB hubs) serving as individual channels for parallel, high-speed gang programming. Each channel c...

By SEGGER Microcontroller GmbH Gold Partner
Emulators, Probes, and Programmers
Flasher ARM

In-Circuit-Flash-Programmer based on the J-Link family for production and in-field-service. Offers fastest flash algorithms available, multiple integration options (RS232...

By SEGGER Microcontroller GmbH Gold Partner
Emulators, Probes, and Programmers
Flasher Hub-12

The Flasher Hub-12 controls up to 12 Flasher Compacts so that they program simultaneously, creating a powerful gang programmer for efficient high-speed parallel programmi...

By SEGGER Microcontroller GmbH Gold Partner
Emulators, Probes, and Programmers
J-Link PRO PoE

J-Link PRO PoE is a specialized programming / debug probe for creating test farms. It can draw power via Ethernet and supplies power to the target either via debug interf...

By SEGGER Microcontroller GmbH Gold Partner
Emulators, Probes, and Programmers
J-Link PRO

J-Link PRO is an enhanced version of the SEGGER J-Link. This emulator supports ARM/Cortex devices. This has an Ethernet interface in addition to the USB interface. This ...

By SEGGER Microcontroller GmbH Gold Partner
Emulators, Probes, and Programmers
Flasher ATE2

Flasher ATE2 is a robust single-board gang programmer with eight independent programming channels. It is designed for high-volume, automated production environments, part...

By SEGGER Microcontroller GmbH Gold Partner
Emulators, Probes, and Programmers
Universal Access Device 2next (UAD2next

The UAD2next combines the state-of-the-art debugging features and CAN with trace capabilities. It can be extended by plugin trace modules supporting e.g. ARM CoreSight pa...

By PLS Development Tools Gold Partner
Emulators, Probes, and Programmers
Flasher Secure

Flasher Secure is a mass production programming system, capable of protecting the vendor’s IP regardless of the production site. It provides full control over the program...

By SEGGER Microcontroller GmbH Gold Partner
Emulators, Probes, and Programmers
J-Trace PRO Cortex-M

J-Trace PRO for Cortex-M enables continuous streaming trace, lifting the limitations by internal buffers and slow data transmission to give the insights you need to optim...

By SEGGER Microcontroller GmbH Gold Partner
Emulators, Probes, and Programmers
J-Link ULTRA+

The J-Link ULTRA+ is three times faster than the industry standard J-Link, at a 3 MBytes/s download speed to RAM. It comes complete with J-Flash, and Unlimited Flash Brea...

By SEGGER Microcontroller GmbH Gold Partner
Emulators, Probes, and Programmers
Flasher Portable PLUS

Flasher Portable PLUS is an extremely portable flash programmer, specifically designed to meet the needs of production-grade flash programming in the field.

By SEGGER Microcontroller GmbH Gold Partner
Emulators, Probes, and Programmers
J-Trace PRO Cortex

J-Trace PRO Cortex provides support for Cortex-A/R/M based microcontrollers. The SuperSpeed USB 3.0 interface enables continuous streaming trace via USB with the full tra...

By SEGGER Microcontroller GmbH Gold Partner
Emulators, Probes, and Programmers
J-Link WiFi

JTAG/SWD debug probe with WiFi interface. Based on a 32-bit RISC CPU, it can communicate at high speed with the supported target CPUs.

By SEGGER Microcontroller GmbH Gold Partner
Emulators, Probes, and Programmers
J-Link EDU Mini

The J-Link EDU Mini is a stripped-down, budget-friendly model of the J-Link debug probe created for educational use. Even with its reduced size, it maintains most J-Link ...

By SEGGER Microcontroller GmbH Gold Partner
Emulators, Probes, and Programmers
Flasher PRO

Flasher PRO is SEGGER’s “almost-anything” flash programmer for microcontrollers, SoCs, and (Q)SPI flashes.

By SEGGER Microcontroller GmbH Gold Partner
Emulators, Probes, and Programmers
Universal Access Device 2pro (UAD2pro)

The UAD2pro offers fast and flexible communication between UDE® Universal Debug Engine on the Host PC and the microcontroller target. Host interface is USB. Target interf...

By PLS Development Tools Gold Partner
Test Accessories and Debugger
Cyclone Production Programmers

Programmer for stand-alone (or cloud-connected) in-circuit flash programming, debug, & test of many NXP MCUs. Sophisticated power mgmt & dynamic data. FX line off...

By P & E Microcomputer Systems, Inc Gold Partner
Test Accessories and Debugger
TRACE32® CombiProbe 2 Compact Trace for NXP Microcontrollers

CombiProbe 2 enables full insight into what an embedded system is doing at run-time. Besides its comprehensive debug capabilities, the trace simplifies system profiling o...

By Lauterbach GmbH Gold Partner
Test Accessories and Debugger
Multilink Debug Probes

Multilink debug probes are BDM/JTAG debug probes for various NXP devices. Universal models support SWO debug in NXP's MCUXpresso IDE. FX model features high-speed com...

By P & E Microcomputer Systems, Inc Gold Partner
Test Accessories and Debugger
TRACE32® Debug and Trace tools for Arm®-based NXP MPUs/MCUs

TRACE32® provides a complete suite of tools for all NXP&#39;s Arm®-based microprocessors. All of these provide unparalleled levels of debug capabilities to get th...

By Lauterbach GmbH Gold Partner
Test Accessories and Debugger
TRACE32® PowerDebug System for NXP Microcontrollers/Microprocessors

PowerDebug is Lauterbach&amp;#39;s powerful, modular, flexible debug system. It provides the broadest coverage of supported chips and core architectures in the em...

By Lauterbach GmbH Gold Partner