Design Files
Quick reference to our
design files types.
2 design files
-
Models
IBIS models for LPC2364-2366-2368-2378
-
Symbols and Footprints
LPC2xxx ORCAD symbols
Arm7™ with 512 kB flash, 58 kB SRAM, Ethernet, USB 2.0 Device, CAN, SD/MMC, and 10-bit ADC
- This page contains information on a product that is not recommended for new designs.
The LPC2368FET100 is a Arm7 microcontroller for embedded applications featuring a high level of integration and low power consumption at frequencies of 72 MHz. Features include up to 256 kB of flash memory, up to 58 kB of RAM, Ethernet MAC, USB Device/Host/OTG, DMA controller, SD/MMC, 4 UARTs, 2 CAN channels, 3 SSP/SPI, 3 I2C, I2S, 8-channel 10-bit ADC, 10-bit DAC, 2 PWM, 4 general purpose timers, low power Real-Time Clock with separate battery supply, and up to 70 general purpose I/O pins. The LPC23xx are pin-compatible to the LPC176x Cortex-M3 series.
sot926-1_3d
Product Details
Block Diagram
Features
- Arm7TDMI-S™ processor, running at up to 72 MHz
- Up to 512 kB on-chip flash program memory with In-System Programming (ISP)
- 32 kB of SRAM on the Arm local bus for high performance CPU access
- 8 kB SRAM for general purpose DMA use also accessible by the USB
- 16 kB SRAM for Ethernet interface. Can also be used as general purpose SRAM
- Dual Advanced High-performance Bus (AHB) system
- Advanced Vectored Interrupt Controller (VIC)
- General Purpose DMA controller (GPDMA) on AHB
- Ethernet MAC with associated DMA controller
- Four UARTs with fractional baud rate generation
- USB 2.0 full-speed device with on-chip PHY
- CAN controller with two channels
- SPI controller
- Two SSP controllers, with FIFO and multi-protocol capabilities
- Three I2C-bus interfaces
- I2S (Inter-IC Sound) interface for digital audio input or output
- SD/MMC memory card interface
- 70 general purpose I/O pins with configurable pull-up/down resistors
- 10-bit ADC with input multiplexing among 6 pins
- 10-bit DAC
- Four general purpose timers/counters with a total of 8 capture inputs
- One PWM/timer block with support for three-phase motor control
- Real-Time Clock (RTC)
- 2 kB SRAM powered from the RTC power pin
- WatchDog Timer (WDT).
- Standard Arm test/debug interface for compatibility with existing tools
- Emulation trace module supports real-time trace
- Single 3.3 V power supply (3.0 V to 3.6 V)
- Four reduced power modes: idle, sleep, power-down, and deep power-down
- Four external interrupt inputs configurable as edge/level sensitive
- Processor wake-up from Power-down mode via any interrupt
- Two independent power domains allow fine tuning of power consumption
- Each peripheral has its own clock divider for further power saving
- Brownout detect with separate thresholds for interrupt and forced reset
- On-chip power-on reset
- On-chip crystal oscillator with an operating range of 1 MHz to 24 MHz
- 4 MHz internal RC oscillator trimmed to 1 % accuracy
- On-chip PLL
Target Applications
- Industrial control
- Medical systems
- Protocol converter
- Communications
Buy/Parametrics
|
|
|
|
|
|
|
|---|---|---|---|---|---|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Documentation
Quick reference to our documentation types.
1-5 of 16 documents
-
Application Note
Guidelines for full-speed USB on NXP's LPC microcontrollers
-
Application Note
Using IAP for LPC2000 Arm® devices
-
Application Note
UUencoding for UART ISP
-
Application Note
PCB layout guidelines for NXP® MCUs in BGA packages
Design Resources
Software
Quick reference to our software types.
2 software files
-
Code Snippets
Sample Code Bundle for LPC23xx/LPC24xx Peripherals using Keil's μVision
-
Code Snippets
Sample Code Bundle for LPC23XX and LPC24XX Peripheral Using KEIL'S ΜVISION
Note: For better experience, software downloads are recommended on desktop.