For best experience this site requires Javascript to be enabled. To enable on your browser, follow our accessibility instructions.

LPC2364FBD100: Arm7^™ with 128 kB flash, 34 kB SRAM, Ethernet, USB 2.0 Device, CAN, and 10-bit ADC

Overview

The LPC2364FBD100 is a Arm7^™ microcontroller for embedded applications featuring a high level of integration and low power consumption at frequencies of 72 MHz. Features include up to 128 kB of flash memory, up to 34 kB of RAM, Ethernet MAC, USB Device/Host/OTG, DMA controller, 4 UARTs, 2 CAN channels, 3 SSP/SPI, 3 I2C, I2S, 8-channel 10-bit ADC, 10-bit DAC, 2 PWM, 4 general purpose timers, low power Real-Time Clock with separate battery supply, and up to 70 general purpose I/O pins. The LPC23xx are pin-compatible to the LPC176x Cortex-M3 series.

Features

Arm7TDMI-S^™ processor, running at up to 72 MHz
Up to 128 kB on-chip flash program memory with In-System Programming (ISP)
8 kB of SRAM on the Arm local bus for high performance CPU access
8 kB SRAM for general purpose DMA use also accessible by the USB
16 kB SRAM for Ethernet interface. Can also be used as general purpose SRAM
Dual Advanced High-performance Bus (AHB) system
Advanced Vectored Interrupt Controller (VIC)
General Purpose DMA controller (GPDMA) on AHB
Ethernet MAC with associated DMA controller
Four UARTs with fractional baud rate generation
USB 2.0 full-speed device with on-chip PHY
CAN controller with two channels
SPI controller
Two SSP controllers, with FIFO and multi-protocol capabilities
Three I2C-bus interfaces
I2S (Inter-IC Sound) interface for digital audio input or output
70 general purpose I/O pins with configurable pull-up/down resistors
10-bit ADC with input multiplexing among 6 pins
10-bit DAC
Four general purpose timers/counters with a total of 8 capture inputs
One PWM/timer block with support for three-phase motor control
Real-Time Clock (RTC)
2 kB SRAM powered from the RTC power pin
WatchDog Timer (WDT).
Standard Arm test/debug interface for compatibility with existing tools
Emulation trace module supports real-time trace
Single 3.3 V power supply (3.0 V to 3.6 V)
Four reduced power modes: idle, sleep, power-down, and deep power-down
Four external interrupt inputs configurable as edge/level sensitive
Processor wake-up from Power-down mode via any interrupt
Two independent power domains allow fine tuning of power consumption
Each peripheral has its own clock divider for further power saving
Brownout detect with separate thresholds for interrupt and forced reset
On-chip power-on reset
On-chip crystal oscillator with an operating range of 1 MHz to 24 MHz
4 MHz internal RC oscillator trimmed to 1 % accuracy
On-chip PLL

Target Applications

Industrial control
Medical systems
Protocol converter
Communications

Features

Arm7TDMI-S^™ processor, running at up to 72 MHz
Up to 128 kB on-chip flash program memory with In-System Programming (ISP)
8 kB of SRAM on the Arm local bus for high performance CPU access
8 kB SRAM for general purpose DMA use also accessible by the USB
16 kB SRAM for Ethernet interface. Can also be used as general purpose SRAM
Dual Advanced High-performance Bus (AHB) system
Advanced Vectored Interrupt Controller (VIC)
General Purpose DMA controller (GPDMA) on AHB
Ethernet MAC with associated DMA controller
Four UARTs with fractional baud rate generation
USB 2.0 full-speed device with on-chip PHY
CAN controller with two channels
SPI controller
Two SSP controllers, with FIFO and multi-protocol capabilities
Three I2C-bus interfaces
I2S (Inter-IC Sound) interface for digital audio input or output
70 general purpose I/O pins with configurable pull-up/down resistors
10-bit ADC with input multiplexing among 6 pins
10-bit DAC
Four general purpose timers/counters with a total of 8 capture inputs
One PWM/timer block with support for three-phase motor control
Real-Time Clock (RTC)
2 kB SRAM powered from the RTC power pin
WatchDog Timer (WDT).
Standard Arm test/debug interface for compatibility with existing tools
Emulation trace module supports real-time trace
Single 3.3 V power supply (3.0 V to 3.6 V)
Four reduced power modes: idle, sleep, power-down, and deep power-down
Four external interrupt inputs configurable as edge/level sensitive
Processor wake-up from Power-down mode via any interrupt
Two independent power domains allow fine tuning of power consumption
Each peripheral has its own clock divider for further power saving
Brownout detect with separate thresholds for interrupt and forced reset
On-chip power-on reset
On-chip crystal oscillator with an operating range of 1 MHz to 24 MHz
4 MHz internal RC oscillator trimmed to 1 % accuracy
On-chip PLL

Target Applications

Industrial control
Medical systems
Protocol converter
Communications

Application Notes

Outline 3d SOT407-1

Outline 3d SOT407-1

Outline 3d SOT407-1

Outline 3d SOT407-1

Outline 3d SOT407-1

.